Repository logo
Log In(current)
  1. Home
  2. Colleges & Schools
  3. Graduate School
  4. Masters Theses
  5. An experimental study of the structure and properties of melt spun polyotymethylene filaments
Details

An experimental study of the structure and properties of melt spun polyotymethylene filaments

Date Issued
March 1975
Author(s)
Khokhani, Maheshchandra Jamnadas
Advisor(s)
Joesph E. Spruiell
Additional Advisor(s)
E. S. Clark
J. L. White
Permanent URI
https://trace.tennessee.edu/handle/20.500.14382/61994
Abstract

The purpose of this study was to experimentally investigate the development of crystallinity, orientation and morphology and its correlation with spinning conditions during melt spinning of polyoxymethylene. Filaments were spun over a range of take-up velocities for each of two mass flow rates (0.58 g/min and 2.ll g/min) at an extrusion temperature of 196°c. Spinline stress and temperature were measured on a running spinline. Crystallinity, birefringence, mechanical properties, wide and small angle x-ray diffraction patterns, and electron micrographs were obtained on as-spun filaments.

The spinline stress in polyoxymethylene filaments increased with the take-up velocity for both mass flow rates, but increased more rapidly for the low mass flow rate case. The larger magnitude of the stress for different mass flow rates resulted from the fact that decreasing the mass flow rate increases both the velocity gradient and cooling rate.

It was found that the decrease in fiber diameter and increase in linear velocity through the cooling medium caused a rapid increase in cooling rate with increased take-up velocity. A decrease in the cooling rate occurred as crystallization began and led to a plateau in the temperature profile. The concept of "continuous cooling transformation curves" was used to compare the kinetics of crystallization during melt spinning to those for quiescent melts. It was found that crystallization in polyoxymethylene can occur several orders of magnitude more rapidly during melt spinning than under quiescent conditions. Since the effect was greatest in the high temperature range, the increase in overall crystallization rate probably resulted from an increase in nucleation rates. This increase in nucleation rate may be caused by the effect that molecular orientation has on the free energy of formation of a nucleus.

The ultimate crystallinity of polyoxymethylene filaments remained almost unchanged with take-up velocity and mass flow rate. The c-axis crystalline orientation function was found to increase with increasing take-up velocity while a-axis orientation function was found to decrease with take-up velocity. These factors were also functions of mass flow rate. Within the experimental accuracy and for the range of variables studied, the orientation factors were determined by the spinline stress.

The changes in crystalline orientation factors, small angle x-ray patterns, and transmission electron microscopy of fiber surfaces were interpreted to indicate that the morphology changed from a "flattened spherulitic" morphology in gravitationally spun filaments to a row nucleated morphology in samples spun under relatively high spinline stresses.

Young's modulus, yield stress and tensile strength were found increase with increase in the c-axis crystalline orientation function and spinline stress. The elongation to break was found to be almost independent of take-up velocity and other variables. The elastic recovery was found to increase with increase in spinline stress and was greater at any given spinline stress for annealed polyoxymethylene samples than for unannealed samples.

Degree
Master of Science
Major
Chemical Engineering
File(s)
Thumbnail Image
Name

Thesis75.K464.pdf

Size

5.78 MB

Format

Adobe PDF

Checksum (MD5)

cc7d3f2245a3fd2dab1360905baad2be


University Libraries

1015 Volunteer Boulevard
Knoxville, TN 37996
865-974-4351

Map & Directions
Donate to the Libraries
  • About
  • John C. Hodges Society
  • Speaking Volumes magazine
  • Outreach
  • Directory
  • Employment
  • Policies
  • Library Intranet
University of Tennessee power T logo

The University of Tennessee, Knoxville
Knoxville, Tennessee 37996
865-974-1000

Events
A-Z
Apply
Privacy
Map
Directory
Give to UT
Accessibility

Built with DSpace-CRIS software - Extension maintained and optimized by 4Science