Repository logo
Log In(current)
  1. Home
  2. Colleges & Schools
  3. Graduate School
  4. Masters Theses
  5. The deformation and fracture of unidirectional boron-aluminum
Details

The deformation and fracture of unidirectional boron-aluminum

Date Issued
June 1977
Author(s)
Welch, Donald Edward
Advisor(s)
Maurice A. Wright
Additional Advisor(s)
D. K. Smith
Walter Frost
Permanent URI
https://trace.tennessee.edu/handle/20.500.14382/60195
Abstract

The purpose of this study was to evaluate experimentally the fracture characteristics of unidirectionally reinforced boron aluminum composite material. In addition, a primary objective was to determine the applicability of the critical stress intensity factor, J-integral and R-curve concepts as failure criteria for this material.

The material examined was 6061 aluminum alloy reinforced unidirectionally with 0.0057 inch diameter boron fibers. The nominal level of reinforcement was fifty volume per cent.

The test specimen geometry used in this program was the center-notched geometry. The nominal specimen sizes tested were one, two and four inches wide. The nominal ratios of crack length to specimen width used were 0, 0.05, 0.1, 0.2, 0.4 and 0.6.

Primary test data consisted of load, load point displacement, crack face displacement, and transverse strain profile near the notch tip.

It was found that the net section stress at failure for center-notched specimens was considerably below that of an unnotched specimen. The net section stress at failure decreased sharply in the range 0 ≤ 2a/w ≤ 0.2. However, for 2a/w ≥ 0.2, this stress remained approximately constant for a given specimen size. It was determined from the crack face displacement data that extensive shear yielding parallel to the fibers occurred in the region above the notch tip. An approximate formula for the height of this zone of shear yielding above the notch tip was derived. Based on this equation, an equation predicting the amount of crack face displacement as a function of applied stress was derived. Reasonable agreement was obtained between the values predicted by this equation and the measured displacements.

The data describing the transverse strain profile near the notch tip was analyzed to determine the order of the stress field singularity near the notch tip. It was found that the expressions presented by Tada for an isotropic material predicted the form of the strain versus distance curve with reasonable accuracy. However, the absolute values of strain predicted by these equations were considerably in excess of the measured strains.

It was also found that the critical stress intensity factor and R-curve techniques had limited utility as failure criteria for this material. The J-integral criterion, however, seemed to reflect a material property.

Finally, a difference in failure modes was observed between the four inch wide specimens and the smaller specimens. The fracture surface of the four inch wide specimens had a brittle appearance, whereas the fracture surfaces of the smaller specimens exhibited much more fiber pullout and unevenness. This was analyzed in terms of the effect of specimen size on the stress distributions present in these samples. It was concluded that edge effects in the smaller specimen sizes could have caused alterations in the stress fields in these specimens. However, comparative material tests revealed significant differences between the parent materials of the four inch wide and the smaller specimens. Thus, the differences in the type of failure observed could not be attributed solely to specimen size.

 
Degree
Master of Science
Major
Engineering Science
File(s)
Thumbnail Image
Name

Thesis77.W453.pdf

Size

9.97 MB

Format

Adobe PDF

Checksum (MD5)

1c4d715e979ca9de09f9c98d19f95cb8


University Libraries

1015 Volunteer Boulevard
Knoxville, TN 37996
865-974-4351

Map & Directions
Donate to the Libraries
  • About
  • John C. Hodges Society
  • Speaking Volumes magazine
  • Outreach
  • Directory
  • Employment
  • Policies
  • Library Intranet
University of Tennessee power T logo

The University of Tennessee, Knoxville
Knoxville, Tennessee 37996
865-974-1000

Events
A-Z
Apply
Privacy
Map
Directory
Give to UT
Accessibility

Built with DSpace-CRIS software - Extension maintained and optimized by 4Science