Repository logo
Log In(current)
  1. Home
  2. Colleges & Schools
  3. Graduate School
  4. Masters Theses
  5. Development and Characterization of Polytrimethylene Terephthalate (PTT) Based Mono- and Bicomponent Meltblown Nonwovens
Details

Development and Characterization of Polytrimethylene Terephthalate (PTT) Based Mono- and Bicomponent Meltblown Nonwovens

Date Issued
August 2001
Author(s)
Beard, John H.
Advisor(s)
Dong Zhang
Additional Advisor(s)
Qin Sun
Kermit E. Duckett
Permanent URI
https://trace.tennessee.edu/handle/20.500.14382/60029
Abstract

Mono and Bi-component polytrimethylene terephthalate (PTT) based meltblown fiber webs were developed on the Reicofil® side-by-side bi-component meltblown line at Textiles and Nonwovens Development Center (TANDEC) located on the campus of University of Tennessee, Knoxville. Main process variables studied were melt temperature, melt throughput, air flow rate, air temperature, and Die to Collector Distance (DCD).

PTT and bico PTT/PP webs were characterized for fiber diameter, bulk density, air permeability, hydro-head, tensile properties, heat shrinkage, and drape ability. PTT/PP webs displayed a non-round cross-sectional and more twisted fiber structure via SEM (Scanning Electrical Microscope). Average fiber diameter of 1.71 to 4.76 µm was achieved with the melt throughput from 0.3-1.5 g/hole/min, melt temperature from 270 to 305°C (520 to 580°F), air temperature from 230 to 310°C (450 to 530°F), air flow rate from 12.5 to 29.2 SCFM/in, DCD from 11 to 19 inches. It was found that the PTT polymer grade for this study was quite suitable for the meltblown process. PTT/PP bicomponent webs show greater resistance to heat shrinkage and enhanced barrier properties.

The PTT fibers have a greater flexural rigidity due to the molecular structure. It seems that the extra CH2 makes the polymer structurally better than PET. PET has a Tm of 265°C, which is greater than the Tm of PTT, 232°C. This translates to longer heat up times and higher energy costs for meltblowing processing. PTT outperforms PET in heat shrinkage. PET acts as if the very mention of heat, it wants to shrink. PET appeared more absorbent, hydrophilic polymer; thus, the moisture content in PET was considerably more than with PTT. These condensation polymers should be dried prior to the meltblowing process.

We have discovered that PTT is a dimensionally stable polyester fiber when heated, although PTT had some shrinkage from 110°C to 130°C. The most shrinkage documented was at 150°C, at approximately 15%. PTT at 190°C and 200°C showed stability with only minimal shrinkage. The PTT fibers that were affected the most at 190° C were the largest fibers. 100% PTT sample 4-3, 5.47μm, shrunk approximately 10% whereas 100% PTT sample 4-1, 4.76µm, had zero shrinkage at 200°C. The smaller diameter fibers tend to be more heat stable.

 
Degree
Master of Science
Major
Textiles, Retail, and Consumer Sciences
File(s)
Thumbnail Image
Name

Thesis2001.B44.pdf

Size

9.24 MB

Format

Adobe PDF

Checksum (MD5)

a0879d957823dd69b9ee942809336ca0


University Libraries

1015 Volunteer Boulevard
Knoxville, TN 37996
865-974-4351

Map & Directions
Donate to the Libraries
  • About
  • John C. Hodges Society
  • Speaking Volumes magazine
  • Outreach
  • Directory
  • Employment
  • Policies
  • Library Intranet
University of Tennessee power T logo

The University of Tennessee, Knoxville
Knoxville, Tennessee 37996
865-974-1000

Events
A-Z
Apply
Privacy
Map
Directory
Give to UT
Accessibility

Built with DSpace-CRIS software - Extension maintained and optimized by 4Science