Repository logo
Log In(current)
  1. Home
  2. Colleges & Schools
  3. Graduate School
  4. Doctoral Dissertations
  5. Design and experimental studies of a generalized bilateral controller for a teleoperator system with a six DOF master and a seven DOF slave
Details

Design and experimental studies of a generalized bilateral controller for a teleoperator system with a six DOF master and a seven DOF slave

Date Issued
May 1996
Author(s)
Chan, Tan Fung
Advisor(s)
Rajiv V. Dubey
Additional Advisor(s)
M. A. Abidi
W. R. Hamel
G. Kawiecki
R. Kress
F. H. Speckhart
Permanent URI
https://trace.tennessee.edu/handle/20.500.14382/59350
Abstract

Generalized bilateral control in teleoperation enables scaling, indexing, impedance control, shared control and the ability to use a non-replica master slave system. This research work focuses on the issues of the design and implementation of generalized bilateral control for a teleoperation system with a redundant slave manipulator. Control laws for complete teleoperation system are derived. Three key issues in the design of the controller for generalized bilateral control with a redundant slave manipulator are investigated: a) kinematic coordination, b) redundancy resolution for slave manipulator, and c) determination of damping and stiffness parameters for master and slave manipulators.

Kinematic coordination requires position and velocity mapping of master and slave end-effectors. Indexing in teleoperation results in an orientation difference between the master end-effector and slave end-effector, which results in different motion directions for base coordinate mapping and hand coordinate mapping. Problems and solutions associated with coordinate mapping with indexing are studied in this research work.

It is proposed to use a weighted least-norm based joint velocity solution to avoid joint limits for redundant joint slave manipulators. A comparison is made with the commonly used gradient projection based method for avoiding joint limits. While the gradient projection method provides the optimal direction for the joint velocity vector within the null space of the Jacobian, its magnitude is not unique and is adjusted by a scalar coefficient chosen by trial and error. It is shown that one fixed value of the scalar coefficient is not suitable even in a small workspace. The proposed manipulation scheme automatically chooses an appropriate magnitude of the self-motion, which is the joint motion that does not result in any end-effector motion. This scheme, unlike the gradient projection method, guarantees joint limit avoidance, and also minimizes unnecessary self-motion.

Damping and stiffness parameters in a teleoperation system allow the master and slave dynamics to be defined by the user. However, many requirements for good teleoperation produce conflicting choices for desired dynamic parameters. Rather than selecting a compromise value for damping and stiffness of master and slave, it is proposed that these parameters be functionally dependent on sensed slave end-effector force and master velocity. A strategy is devised which provides better quality teleoperation under a variety of circumstances than is achievable with constant dynamics. It is shown that the proposed scheme improves the tracking in free space and along a surface by the slave end-effector without increasing impact forces.

One of the problems with most master manipulator designs is that the mechanical impedance of the master end-effector is different in different directions. Therefore, moving the master end-effector in different directions requires different force/moment, and an applied force/moment does not result in motion in the same direction. In this dissertation, we discuss the kinematic design issues related to the master impedance.

A 6 degree-of-freedom (DoF) Kraft teleoperation hand controller (master) and a 7 DoF Robotics Research Cooperation manipulator (slave), are used to build a test-bed for generalized bilateral control. Extensive C code for complete system operation along with necessary drivers for different hardware were developed as part of this work. A relatively difficult assembly task was used to test the effectiveness of the system.

 
Degree
Doctor of Philosophy
Major
Mechanical Engineering
File(s)
Thumbnail Image
Name

Thesis96b.C337.pdf

Size

22.1 MB

Format

Adobe PDF

Checksum (MD5)

6b7f8e122b7bb1ce3b6dd14de73f34c4


University Libraries

1015 Volunteer Boulevard
Knoxville, TN 37996
865-974-4351

Map & Directions
Donate to the Libraries
  • About
  • John C. Hodges Society
  • Speaking Volumes magazine
  • Outreach
  • Directory
  • Employment
  • Policies
  • Library Intranet
University of Tennessee power T logo

The University of Tennessee, Knoxville
Knoxville, Tennessee 37996
865-974-1000

Events
A-Z
Apply
Privacy
Map
Directory
Give to UT
Accessibility

Built with DSpace-CRIS software - Extension maintained and optimized by 4Science